2015 · 19 citations · 10 references
EngineeringMaterials EngineeringMaterials ScienceElectronic MaterialsSemiconductor DevicesSemiconductor MaterialsPhotovoltaic DevicesPhotovoltaic MaterialsSemiconductor Device MaterialsSemiconductor Thin FilmsSolar Cell MaterialsSolar CellsAbsorber MaterialsCadmium TellurideCell EfficiencyEnergy Conversion EfficiencyLight-absorbing LayersNumerical Stability AnalysisPhotovoltaic Performance AnalysisPower Conversion Efficiency
The polycrystalline ultra-thin cadmium telluride (CdTe) is familiar as the potential solar cell material for its higher efficiency, cost-effective, cell stability and clean generation of solar electricity. In this study, a numerical analysis has been performed utilizing AMPS (Analysis of Microelectronic and Photonic Structures) simulator to examine the cell performances (V <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">oc</sub> , J <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">sc</sub> , FF and conversion efficiency) of ultra-thin CdTe solar cell. During the research, reduction of CdTe layer was done in the proposed cell and found that 1μm absorber layer is enough for acceptable range for cell conversion efficiency. The possibility of this ultra-thin CdTe absorber layer was examined, as one with 100 nm ZnTe back surface field (BSF) layer to minimize the recombination losses at the back contact and to reduce the barrier height in the valence band of the proposed cell. Higher conversion efficiency of 22.53% (J <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">sc</sub> = 24.28 mA/cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> , FF = 0.875, V <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">oc</sub> = 1.06 V) has been achieved with only 0.8 μm of CdTe absorber layer along with 100 nm ZnTe BSF where as conversion efficiency is 18.68% (J <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">sc</sub> = 21.47 mA/cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> , FF = 0.85, V <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">oc</sub> = 1.02 V) without BSF layer. Moreover, the proposed CdTe solar cell showed better stability as the normalized efficiency of the proposed cell linearly decreased with the increasing operating temperature at the gradient of -0.16%/°C.
10
Marc Burgelman, Johan Verschraegen, S. Degrave et al. · Progress in Photovoltaics Research and Applications · 2004 · 535 citations
Development of efficient and stable back contacts on CdTe/CdS solar cells
D.L. Bätzner, Alessandro Romeo, H. Zogg et al. · Thin Solid Films · 2001 · 158 citations
Applications of AMPS-1D for solar cell simulation
Hong Zhu, Ali Kaan Kalkan, Jingya Hou et al. · AIP conference proceedings · 1999 · 134 citations
High efficiency CdTe solar cells by close spaced sublimation
Chris Ferekides, J. Britt, Yujing Ma et al. · 2002 · 85 citations