Proceedings of SPE/IADC Drilling Conference · 1992 · 26 citations · 0 references
EngineeringCivil EngineeringDrillingDrilling EngineeringRock MechanicsDrill Bit TechnologyDrill String MechanicsDrilling EquipmentDrilling MechanicsDrilling OperationsRotary DrillingBit VibrationDrillstring DynamicsDrillstring MechanicsNumerical ModellingOperating ConditionsRotary Drilling DynamicsTorsional Vibration ControlTorsional Vibration Modeling
PDC Bit Dynamics C.J. Langeveld C.J. Langeveld Shell Research B.V. Search for other works by this author on: This Site Google Scholar Paper presented at the IADC/SPE Drilling Conference, New Orleans, Louisiana, February 1992. Paper Number: SPE-23867-MS https://doi.org/10.2118/23867-MS Published: February 18 1992 Cite View This Citation Add to Citation Manager Share Icon Share Twitter LinkedIn Get Permissions Search Site Citation Langeveld, C.J. "PDC Bit Dynamics." Paper presented at the IADC/SPE Drilling Conference, New Orleans, Louisiana, February 1992. doi: https://doi.org/10.2118/23867-MS Download citation file: Ris (Zotero) Reference Manager EasyBib Bookends Mendeley Papers EndNote RefWorks BibTex Search Dropdown Menu nav search search input Search input auto suggest search filter All ContentAll ProceedingsSociety of Petroleum Engineers (SPE)SPE/IADC Drilling Conference and Exhibition Search Advanced Search AbstractThe poor performance of PDC bits in harder formations is caused by downhole vibrations. However, proper operating conditions (i.e. low rotary speed and high weight on bit) and new technology for vibration control (anti-whirl PDC bits and a soft-torque rotary system) can successfully extend the application of PDC bits to harder formations. This conclusion is based on numerical modelling of PDC bit/drillstring assemblies and is supported by recent developments in PDC bit technology and torsional vibration control systems. The PDC bit model is fully dynamic and three-dimensional and is used to simulate normal rotary drilling. Sensitivity analyses of different PDC bit designs show bit-induced torsional, axial and lateral vibrations. Moreover, these analyses show that conventional PDC bits tend to whirl backward, resulting in reduced penetration rates and bit life. Anti-whirl PDC bits effectively reduce this tendency when run under the proper operating conditions of low rotary speed and high weight on bit.IntroductionDownhole measurements and numerical analyses clearly demonstrate that, during normal rotary drilling, the drillstring vibrates in several modes of vibration. Downhole vibrations frequently result in inconsistent bit performance, drillstring failure, problems with directional control, lack of measurement while drilling (MWD) signal detection and borehole instability. In particular in harder formations severe vibrations cause particular in harder formations severe vibrations cause premature polycrystalline diamond compact (PDC) bit premature polycrystalline diamond compact (PDC) bit failure. This has led to the generally accepted field practice that PDC bits are run mainly in soft to practice that PDC bits are run mainly in soft to medium-hard formations. This is rather disappointing, considering artificial diamond cutters can cut very hard rock under controlled conditions. The work presented in this paper was initiated to investigate the presented in this paper was initiated to investigate the effects of PDC-bit-induced vibrations and to address the problems associated with drilling harder formations.For a better understanding of the complex phenomena experienced during drilling, numerical phenomena experienced during drilling, numerical simulation of the drillstring behaviour is essential. In general, the computer programs for drillstring dynamics reported in literature deal with boundary conditions at the bit only or use a simple bit model. The drilling motion of the bit, including formation removal, is not taken into account. On the other hand, dedicated PDC bit models are kinematic, i.e. the bit motion is prescribed, and two-dimensional, and therefore cannot be used for the investigation of the dynamic behaviour of PDC bits. Recently a three-dimensional PDC bit model was presented by Behr et al. Again it is a kinematic presented by Behr et al. Again it is a kinematic model, although it is possible to compute the cutting forces for more complex bit motions like bit whirl. Brett uses an experimentally derived PDC bit model and a simple mass-spring model of the torsional drillstring motion.P. 227 Keywords: penetration rate, revolution, torsional, whirl, drilling, reactive upward force, bit design, frequency, rotary speed, dynamic behaviour Subjects: Drill Bits, Bit design This content is only available via PDF. 1992. IADC/SPE Drilling Conference You can access this article if you purchase or spend a download.