1c:I[419806,["/_next/static/chunks/bb923814e1f4d2e9.js","/_next/static/chunks/dd3ee9f5b7716ca6.js","/_next/static/chunks/4204a0ae82542ca8.js","/_next/static/chunks/30036bedc5269936.js","/_next/static/chunks/6e1aa89a642f40be.js","/_next/static/chunks/cd5e572bc3e4eb92.js","/_next/static/chunks/8ffd0b71567920d8.js","/_next/static/chunks/67ea6dfd21f16c5f.js","/_next/static/chunks/24eb4379f68013fd.js","/_next/static/chunks/b8cd775ffdf935bd.js","/_next/static/chunks/983103cd9eb7b428.js","/_next/static/chunks/d4ac9dcf27f6ff52.js","/_next/static/chunks/294b9525248c8e5f.js"],"default"] 1d:T41b,We have synthesized the novel composite membranes composed of sulfonated polyimide nanofibers and sulfonated polyimide for proton exchange membrane fuel cell. It was clear that the polyimides within nanofiber were significantly oriented or aggregated when electrospun; as the result, the membrane stability, such as oxidative and hydrolytic stabilities, of the composite membrane was significantly improved with an increase in nanofiber, and oxygen permeability of the composite membrane also decreased when compared to that determined in the membrane without nanofibers. In addition, the proton conductivity of the membrane in the parallel direction indicated a significantly higher value when compared to that determined for the membrane in the perpendicular direction or for the membrane without nanofibers prepared with conventional solvent-casting method. Consequently, nanofibers proved to be promising materials as a proton exchange membrane and the composite membrane containing nanofibers may have potential application for use in fuel cells.1e:T4c0,Tunable density, thermally and mechanically stable, elastic, and thermally insulating sponges are required for demanding applications. Hierarchically structured sponges with bimodal interconnected pores, porosity more than 99%, and tunable densities (between 7.6 and 10.1 mg/cm³) are reported using polyimide (PI) as high temperature stable polymer. The sponges are made by freeze-drying a dispersion of short PI fibers and precursor polymer, poly(amic acid) (PAA). The concept of "self-gluing" the fibrous network skeleton of PI during sponge formation was applied to achieve mechanical stability without sacrificing the thermal properties. The sponges showed initial degradation above 400 and 500 °C in air and nitrogen, respectively. They have low thermal conductivity of 0.026 W/mK and thermal diffusivity of 1.009 mm²/s for a density of 10.1 mg/cm³. The sponges are compressible for at least 10 000 cycles and good thermal insulators even at high compressions. These fibrous PI sponges are promising candidates for potential applications in thermal insulation, lightweight construction, high-temperature filtration, sensors, and catalyst carrier for high-temperature reactions.1f:T4d9,Sub-nanometer materials have received wide attention due to their unique properties in recent years. Most studies focus on the preparation and properties investigation of the inorganic sub-nanometer materials, while there are few reports on organic especially polymeric sub-nanometer materials such as sub-nanometer fiber due to the obstacles with respect to fabricating such small nanofibers. In this work we prepare PAA nanofibers with diameters ranging from hundreds of nanometers down to sub-nanometer via electrospinning from a polyamic acid (PAA) with ultrahigh molecular weight. The morphologies and size of the electrospun ultrathin nanofibers are characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM). AFM images combined with theoretic calculations show that sub-nanometer fiber of approximate 0.17-0.63 nm only containing one molecular chain was generated via electrospinning from ultra-dilute PAA solutions for the first time. These quite small sub-nanometer fibers would open a new area of electrospinning and provide further explorations on the production and application of electrospun sub-nanometer fibers with sing

	Year	Citations

References