LUTPub (LUT University) · 2014 · 42 citations · 0 references
Open access
EngineeringElectrical EngineeringMechanical EngineeringElectric MachinesHeat TransferThermal AnalysisCooling SystemsElectromagnetic Torque ProductionInduction MachinesMachine CoolingPermanent Magnet MachinesSynchronous MachinesLiquid CoolingLiquid-cooled MachinesPermanent Magnet Synchronous Machines
In the design of electrical machines, efficiency improvements have become very \nimportant. However, there are at least two significant cases in which the compactness of \nelectrical machines is critical and the tolerance of extremely high losses is valued: \nvehicle traction, where very high torque density is desired at least temporarily; and \ndirect-drive wind turbine generators, whose mass should be acceptably low. As ever \nhigher torque density and ever more compact electrical machines are developed for \nthese purposes, thermal issues, i.e. avoidance of over-temperatures and damage in \nconditions of high heat losses, are becoming of utmost importance. The excessive \ntemperatures of critical machine components, such as insulation and permanent \nmagnets, easily cause failures of the whole electrical equipment. In electrical machines \nwith excitation systems based on permanent magnets, special attention must be paid to \nthe rotor temperature because of the temperature-sensitive properties of permanent \nmagnets. The allowable temperature of NdFeB magnets is usually significantly less than \n150 ˚C. The practical problem is that the part of the machine where the permanent \nmagnets are located should stay cooler than the copper windings, which can easily \ntolerate temperatures of 155 ˚C or 180 ˚C. Therefore, new cooling solutions should be \ndeveloped in order to cool permanent magnet electrical machines with high torque \ndensity and because of it with high concentrated losses in stators. \nIn this doctoral dissertation, direct and indirect liquid cooling techniques for permanent \nmagnet synchronous electrical machines (PMSM) with high torque density are \npresented and discussed. The aim of this research is to analyse thermal behaviours of \nthe machines using the most applicable and accurate thermal analysis methods and to \npropose new, practical machine designs based on these analyses. The Computational \nFluid Dynamics (CFD) thermal simulations of the heat transfer inside the machines and \nlumped parameter thermal network (LPTN) simulations both presented herein are used \nfor the analyses. Detailed descriptions of the simulated thermal models are also \npresented. Most of the theoretical considerations and simulations have been verified via \nexperimental measurements on a copper tooth-coil (motorette) and on various \nprototypes of electrical machines. \nThe indirect liquid cooling systems of a 100 kW axial flux (AF) PMSM and a 110 kW \nradial flux (RF) PMSM are analysed here by means of simplified 3D CFD conjugate \nthermal models of the parts of both machines. In terms of results, a significant \ntemperature drop of 40 ̊C in the stator winding and 28 ̊C in the rotor of the AF PMSM was achieved with the addition of highly thermally conductive materials into the \nmachine: copper bars inserted in the teeth, and potting material around the end \nwindings. In the RF PMSM, the potting material resulted in a temperature decrease of \n6 ̊C in the stator winding, and in a decrease of 10 ̊C in the rotor embedded-permanentmagnets. \nTwo types of unique direct liquid cooling systems for low power machines are analysed \nherein to demonstrate the effectiveness of the cooling systems in conditions of highly \nconcentrated heat losses. LPTN analysis and CFD thermal analysis (the latter being \nparticularly useful for unique design) were applied to simulate the temperature \ndistribution within the machine models. Oil-immersion cooling provided good cooling \ncapability for a 26.6 kW PMSM of a hybrid vehicle. A direct liquid cooling system for \nthe copper winding with inner stainless steel tubes was designed for an 8 MW directdrive \nPM synchronous generator. The design principles of this cooling solution are \ndescribed in detail in this thesis. The thermal analyses demonstrate that the stator \nwinding and the rotor magnet temperatures are kept significantly below their critical \ntemperatures with demineralized water flow. A comparison study of the coolant agents \nindicates that propylene glycol is more effective than ethylene glycol in arctic \nconditions.